2020年9月24日星期四

MB SD C4 Reset SBC Brake on Mercedes W211

 

One of the MB SD Connect 4 users reported that he cannot reset SBC brake for Mercedes-Benz W211 2005 with new DAS/XENTRY Star diagnostic software. Actually it will. Please follow the instructions below.
How to use Benz star diagnostic Platinum Edition to reset SBC?

When you choose SBC system, it will have an option, SBC RESET, after you enter this option, you will see special function, enter this and it will ask for the password, for this password, just fill anything you like, then click next step, then click ok, then follow the prompt to do next.
Super MB Star Software Platinum Edition is form here

​Proper steps here:

Connect Mb Star C4 Diagnostic mux with W211 and laptop.

Start Star diagnosis software.

Select chassis: SBC – Sensotronic Brake Control
34-1
​Select Control unit adaptions, and click on the tick button to continue.
34-2
Select Special functions and click on the tick button to continue.
34-3
Set a password as you like, then to continue.
34-4
Click OK.
Follow the instruction on the screen to reset SBC brake.

Note

If you got German language Star diagnostic software, then follow instruction here
​SBC TOOLS RESET
It started like most of them…….
As a request !!
So it was a combination, of a faulty SBC, common sence, LOTS of time and GUTS to figure this out

Make sure engine is running !!!

In Developer mode you need to go to Entwickelingsdaten –> ansteueringen –> Gesamstliste aller Ansteuerungen

to see how many times brake has been pressed there is a line that says: Bremsenzahler (DJ_GetBrLive) or DJ_GetBrLiveTime

then 1 line down there you see Bremsenzahler aktualisieren und Lebensdauerzahler F neu berechenen –> click it !
Parameter uINBR = 0
then click F3

1 line down Bremsenzahler auf beliebigen Wert setzen (DJ_SetNBr) –> click it
Parameter uINBR = 0
then click F3
then scroll down untill you see the line’s :

Lebensdauerzahler F neu berechenen (DJ_CalcLiveTime)
Parameter uINBR = 0
then click F3

Lebensdauerzahler F neu berechenen und schreiben (DJ_BuildAndWriteF)
Parameter uINBR = 0
then click F3

Log out of SBC !!
log out of verhicle !!

let engine run at least 10 minutes or drive at least 10 minutes

If no coils are damaged, SBC fault code is not AKTUEL nomore

Note:
(Dj_setNBr) Here you SET new brake counter value back to 0
(Dj_setNBr) uINBR = 0

Resetting break counter to zero is in my opinion, not messing with …..

each time SBC powers up it checks itself time after time
If there occures any problem in SBC unit with valve, brushes or whatever, it will go into error anyway. that you will NOT be able to erase in Dev mode

If you switch on contact of Brand new MB with SBC and press break 300.000 times it will go into this so called “error” you wanna say SBC is broken then ? without driving a milimeter ?

No it’s indication to have SBC unit checked by MB workshop $$

Yes it’s true that MB has to replace Faulty SBC units for free
since Factory will pay all there labor & material
But most Dealers try to have costumer pay for this procedure claiming costumers car has no a Dealer serviced History

 

MB SD C4 Star Diagnostic Tool With Vediamo V05.01.01 Development and Engineering Software Plus EVG7 Tablet PC

Best Quality V2020.09 MB SD Connect Compact C4 Star Diagnostic TooL With Vediamo and DTS Engineering Software

没有评论:

发表评论