Xhorse Dolphin XP005 Error Code 29 Solution

 

Here share the solution to resolve Xhorse Dolphin XP005 Error Code 29.

Problem:

Use Dolphin XP005 to cut key, it can’t cut key normally. Try the height adjustment, the X-axis motor test and the Z-axis motor test, all fail and get the error code: 29. I also do a conductivity test, the cutter and clamp are fine, but the probe and clamp are showing always tests on.

Engineer replied:

The milling cutter shorted out, please follow the following post to check

Xhorse Dolphin XP005 probe and milling cutter abnormal conductivity detect method

After that, clean the iron filings inside.

Check the Cylinder Compression using TECHSTREAM (TIS) Software

 

Check the Cylinder Compression

INSPECT COMPRESSION
1). Manually using the pressure gauge (cylinder compression pressure).
* Remove Cylinder Head cover.
* Remove 4 Ignition Coil.
* Remove 4 Spark Plug (Busi).
* Remove connector Fuel Injector.

-Install compression gauge to the Spark Plug port.
-Place the throttle on fully open.
-START (cranking) the engine, and measure through the compression gauge.

* 1471 kPa (15.0 kgf/cm², 213 psi)
* Minimum pressure: 1079 kPa (11.0 kgf/cm², 156 psi)
* Differences between the cylinder: 98 kPa (1.0 kgf/cm², 14 psi or less)

-Use fully charged-battery, So the Engine Speed while START can reach 250 rpm or more.
-Inspect the another cylinder with the same way.

2). Using TECHSTREAM (TIS) Software.
#Check the Cylinder Compression
* Connecting MINI-VCI adapter to OBDII Diagnostic Port on your Car. Read More: Install MINI-VCI J2534 Driver untuk TECHSTREAM (Toyota TIS) Software
* Once connected, click the “Engine and ECT” on “System Selection Menu”.

* Click “Active Test” on the left side menu, and “Active Test Selection” displayed as Figure 1.3 below. Choose “Check the Cylinder Compression” from the “Active Test List”, then click “OK”.

On this “Active Test”, Fuel and Ignition all cylinders are cut, cranking occurs for approximately 10 seconds. Then, each cylinder measures the Engine rpm. If a cylinder’s Engine rpm is higher than the other, that cylinder’s compression pressure is compared to the other, and is determined whether it is low or not.

Operate with Ignition ON, Engine OFF, Shift Selector in P (AT) or Neutral (MT).
-Command: ON/ OFF.

This test requires the Engine to crank continuously for approximately 10 seconds. Push button ignition switches may require button to be held down for approximately 5 to 10 seconds to complete this test. Please connect a battery charger if insufficient battery voltage.*

* Change monitoring “Data List” to “Compression”, we need to monitoring the “Engine Speed of Cyl #1 – #4”. Read More: Monitoring Parameter Data List on Your Car (Real Time) using TECHSTREAM (TIS Software).
* Click on “<” to activate (ON), and “>” to deactivate (OFF).
* When the “Check the Cylinder Compression” ON, cranking/ START the Engine for approximately more than 10 seconds, and please monitoring the Engine Speed from each cylinder (Cyl #1 – #4).

iProg programmer do odometer programming for Honda MB91F061BS

 

This post show a feedback on iProg programmer do odometer programming for Honda MB91F061BS.

Notice:You need have scripts,otherwise you can not do it.

Preparations:

Newest iProg Pro Plus iProg+ v87 v84 v82 Free Download

 

Procedures:

Build connection by iProg programmer

Then run iProg software,then select “Honda MB91F061BS”

Click “Read EEPROM”,wait processing

Now enter a new value

Click “Write EEPROM”

Wait processing,when “Write EEPROM” ok in message box

The dashboard will restart

After dashboard light on,it will show a new value you input just now.

Caterpillar electronic technician

 

Caterpillar electronic technician 2022A (replaces CAT ET 2021C, 2021B, 2021A, 2020A, 2019C, 2019B) with Win Flash future is an updated version of the caterpillar dealer diagnostic software that can help technicians to diagnose existing and potential problems with their electronically controlled Caterpillar Engines and Machines.

Pls note: if you buy cat 2022A software, we will send the software by email, please download and install the software into your laptop.then send the Todesk id and password to us,we will activate it for you soon for free one time.

The Built-in Factory Password Generator: the CAT 2022A software include the 10 Bit factory passwords when you push the ctrl+f2 shortcut button,you can open the 10 bits of password generator.

Cat works with the Caterpillar Communication Adapters family.

CAT 2022A software can work with Windows 7 32 bit, Windows 7 64 bit, Windows 8/8.1 32 bit, Windows 8/8.1 64 bit, Windows 10 32 bit, Windows 10 64 bit

If you want to learn more, you can contact with us :sale@cnautotool.com or you can search on our store directly : https://www.cnautotool.com